3000GT / Stealth / GTO Fastener Identification System

Click on a fastener to view the full resolution image. Fasteners with a green border are confirmed on multiple cars. Fasteners with a yellow border are confirmed on one car. Fasteners with a red border weren't clearly labelled, so a best guess was taken. If conflicting fasteners were found on two cars, both are included and marked red. If conflicting fasteners were found on three or more cars, only the most common is included and marked green.

Screw Identification

Fuel Filler Neck to Frame Near Gas Cap (x3)

Wooden Spare Tire Cover Hinge to Frame (x2 Per Side)

Ignition Switch Component to Steering Column (x1)

Rear Interior Panel to Frame Near Rear Seatbelt Retractor (x2 Per Side)

Rear Passenger Exhaust Bracket to Frame (x1)

Ground Wire for Power Antenna to Chassis (x1)

Door Window Belt Molding to Door (x2 Per Side)

Buzzer (MB649187) to Right Center Console Support Bracket (x1)

Center Console to Bracketry (x2 Per Side)

Center Console to Frame (x1 Per Side, Behind "C" Shaped Trim Clips)

Support for Center Hatch Trim to Frame (x1 Per Side)

Door Power Window / Lock Control Panel to Door Card (Total x3 Per Side)

Vents in Door Sill to Frame (x2 Per Side)

Door Sill Step Guard to Frame (x4 Per Side)

Rear Vinyl Panel to Frame (x2 Per Side, Near Seatbelt Retractor)

ECU Harness to Passenger Floor Tray (x4)

Front Seatbelt Pass-Through Bezel to Frame (x1 Per Side)

Front Windshield Lower Valence to Frame (x6)

Center Hatch Trim to Frame (x4, Along Top)

Hatch and Fuel Door Release Lever Assembly to Frame (x2 Per Side)

Hatch Ground Strap to Frame Beneath Latch (x1)

Side Hatch Trims to Frame (x1 Per Side, Near Hatch Strut)

Side Hatch Trims to Frame (x1 Per Side, Along Top)

Interior Harness to Center Console Support Bracket (x1 Per Side)

Privacy Shade / Tonneau Cover Mount to Frame (x1 Per Side)

Reverse Light / Reflector Assembly to Bumper (x2 Per Side, Stealth Models)

Rear Corner Light Bezel to Rear Corner Light (x2 Per Side, RT Models)

SRS Harness to Left Center Console Support Bracket (x2)

Stainless Door Molding to Frame (x12 Per Side)

Steering Column Stalk Mount (MB29615X) to Steering Column (x2)

Steering Column Stalks to Steering Column (x2 Per Side)

Plastic Trim Under the Dash Near the Door to Frame (x1 Per Side)

Rear Vinyl Panel to Frame (x1 Per Side, 2" Below Rear Seat Anchor)

Rear Vinyl Panel to Frame (x1 Per Side, Under Rear Seat Bottom)

Nut Identification

Lower Control Arm to Subframe (Rear, Outer) (x1 Per Side)

Air Conditioning Line to Evaporator Core (x1)

Air Conditioning Line to Frame in Front of Left Motor Mount (x1)

Brake Line to Passenger Strut Tower (x1)

Cam Angle Sensor to Cam Angle Sensor Bracket (x1)

Cruise Control Box to Cruise Control Box Bracket (x4)

Hard Line Bracket to Frame Behind Subframe (x1)

Rear Bash Bar Support to Frame (x4 Per Side)

Rear Washer Fluid Resevoir to Frame (x3)

Bracket Under Dash to Frame Near Firewall in Center (x2)

Standard Bolt Identification (WIP)

Your Fastener's Information

Enter all information available, as accurately as possible. The system will retrieve a list of the closest matches. Dropdowns are exclusive (will hide entries that would otherwise match), text boxes will find the closest match.

Region of Car:

A - Engine Compartment (Under the Hood, Excluding Motor / Transmission)
B - Engine and Transaxle (Motor and Transmission)
C - Dash Panel (and Therebehind)
D - Instrument Panel and Floor Console (Gauges and Center Console)
E - Interior
F - Luggage Compartment (Hatch)
G - Front Fenders & Bumper
H - Rear Fenders & Bumper
I - Under Car

Colour:

Head Marking:

Options in square brackets represent meta options describing the head, not literal text.

Head Size:

Shank Diameter:

If the bolt in question has a tapered grip, use the diameter of the threads.

Grip Length (Unthreaded Portion):

If threads start at the head, enter 0. If unknown, leave blank.

Thread Length (Threaded Portion):

If unknown, leave blank.

Thread Pitch:

Captive Washer Diameter

Not attached to head - loose, but retained by threads. If not present, enter 0. If unknown, leave blank.

Captive Split Washer Diameter

Not attached to head - loose, but retained by threads. If not present, enter 0. If unknown, leave blank.

Thread Notch Present

Describes a slice cut into the tip of the threads.

Thread Taper Present

Describes a narrowing of the threads at the tip.

If checked, text field searches will include results where the database does not have a value stored in that field (if they exist, they will be at the top of the results).

Include Results Without Recorded Text Fields

Your Search Results

Special Bolt Identification

Washers and nuts shown in the order they stack.